Poolcare Leisure Ltd are offering a reduced service during the current situation with Covid-19.

Please contact us on07974 268804 for technical advice/emergency call outs or alternatively email us on service@poolcareleisure.com 

 or for account queries, email accounts@poolcareleisure.com 

We hope all of our clients are staying safe and well and we look forward to resuming normal service as soon as possible. Further updates will be posted here.



Caldera Spas

We specialise in the Caldera range of Spa's. With nearly 40 years of experience in making Spa's Caldera is aruably one of the leadibg the leading brands. In our warwick based showroom we have the Marion and the Aventine spa on display. We can supply the entire Caldera range.

How to maintain your spa pool for best results

The amount of chemicals required depends on how much your spa is used and whether it is used for domestic or commercial purposes. As a rough guide, a small spa requires as much disinfectant as an average sized swimming pool. To ensure that the disinfectant is effective, the water must be sparkling clean and the chemistry must be right. Follow the step by step instructions below to achieve the best results. A 4 in 1 test kit is recommended for this purpose.

Step 1:
Estimate the volume of your spa or ask us to help with your calculations. Most private spas have 1000-5000 litre capacity. Commercial spa's can have a much higher capacity.

Step 2:
Check the pH - pH is a simple measure of acidity or alkalinity. The pH of spa water should always be above 7.0 (measured at room temperature, not warm) so be sure to take a sample and allow it to cool down to room temperature before testing to avoid corrosion of the heater and filter. However, it should not be higher than 7.8 as this will reduce the disinfectant efficiency, especially that of chlorine which is more effective at the lower end of the recommended pH range. To increase or decrease the pH simply raise or lower the total alkalinity following step 3.

Step 3:
Adjust the total alkalinity - ensure that the total alkalinity is in the range of 125 - 175 ppm.

  •   To increase the total alkalinity by 10 mg/L add 17g of sodium bicarbonate for each 1000 L of spa water.

  •   To lower the total alkalinity by 10 mg/L add 20 mL of hydrochloric acid or 24g of dry acid (sodium hydrogen sulphate) for each 1000L of spa water.


When dosing the spa water with chemicals always OPERATE THE FILTER PUMP but DO NOT use the air blower or the venturi.

Step 4:
Disinfect the water - this is essential to kill all the harmful microorganisms. When using lithium as your primary sanitizer add 50 grams per 1000 litres at start up, then 12 grams per 1000 litres as a daily dose. Always add product to water, NOT water to product.

When using bromine as your primary sanitizer, place 4-6 tablets into the floating dispenser. In order to maintain the correct free bromine level in your spa water keep your dispenser full of bromine tablets at all times.

Note: Bromine or Lithium Hypochlorite is the preferred disinfectant in spas as the liquid chlorine - sodium hypochlorite - goes off with storage and dosing may need to be increased. Calcium hypochlorite (dry chlorine) is not recommended in spas as it causes scaling of the heater element.

Another excellent way to sanitize your spa is with Bayrol Products, These products are chlorine & bromine free. These products can be purchased on our sister site at www.poolcareproducts.co.uk 

Step 5:
Shock dose - after heavy use of the spa or on at least a weekly basis, shock dose the water. 


What to do

  •  Make sure your spa pool water is not hotter than 40º C. An ideal range is 35-37° C. Use a thermometer to check.

  • Spa use should be restricted to 20 minutes at any given time at maximum temperatures to minimise heat stress.

  •  Extended exposure times can promote skin infections.

  •  A spa should not be used after heavy drinking, if you have been seriously ill, have had recent surgery, are pregnant or if you have a heart condition.

  • Keep your head out of the water. Do not swallow spa water.

  • Clean your spa filter regularly, according to the manufacturer's instructions or at least fortnightly. Use our spa cleaner for this job. High temperatures accelerate the release of body oils and greases into the water.

Empty your spa and thoroughly clean:
at least every 3 months or up to fortnightly if it is heavily used;
- if it scales up the walls, foams excessively or looks grimy; and
- if dosing of disinfectant does not eliminate smells

Poolcare Leisure Logo